14/04/17: Bought CVpal, Frequency Central PCBs (Vogue VCF, two oscillators, ADSR), NLC PCBs (dual LFO, two sloths)
22/04/17: Completed CVPal, bought 2hp mult
01/06/17: Bought Doepfer DIY kit
01/07/17: A few bought modules - ebay, MuffWiggler boards, EMISmusic (Doepfer a138b,a132-3, a110-1, a130)
25/07/17: Started building case
27/07/17: Bought non-functioning Frequency Central VCO
02/08/17: Bought DSO138 oscilloscope and 2206 function generator
04/08/17: Built DSO138 oscilloscope and 2206 function generator
05/08/17: Completed case
14/08/17: Bought Doepfer a138-2 and Intellijel Unity Mixer second hand from MuffWiggler board
15/08/17: Completed Two Frequency Central Routemaster power supplies. Bought new soldering iron (ERSA Analog 60) as old one died
16/08/17: Completed NLC Dual LFO, fixed the broken FC VCO, completed FC ADSR.
Bought second hand MN mult, Intellijel mult and 2hp Trim from MuffWiggler boards
17/08/17: Completed FC Vogue filter. Bought new oscilloscope (Rigol DS1058E)
20/08/17: Completed FC VCO. Calibrated VCOs and Vogue filter. Also bought a DIY Mutable Ripples PCB (scary SMT soldering !) as well as a FC S&H/Noise PCB
24/08/17: Started building two NLC Sloths and FC S+H/Noise
25/08/17: Ordered O+C PCB
24/08/17: Completed two NLC Sloths and FC S+H/Noise
17/09/17: Completed a passive multiple
21/09/17: Bought a second a100 DIY kit (power supply, bus boards and rails) as well as a Doepfer a151 voltage-controlled sequential switch
07/10/17: Bought a CV.OCD MIDI to CV interface
19/12/17: Bought a Mutable Instruments Clouds
28/12/17: Bought Mutable Instruments Rings and Links
10/02/18: Built and debugged two MI Ripples (DIY SMT)
18/02/18: Nicky bought me a Make Noise Function for my birthday!
24/02/18: Built an Ornament and Crime module
01/03/18: Built two Mutable Instruments Veils quad VCAs
07/03/18: Bought Doepfer a140 ADSR and a170 Dual Slew second hand from MuffWiggler board
08/03/18: Built two three-channel passive attenuators
21/03/18: Built two MI Braids. Big reorganisation of modules in the case to balance the current draw between the two power supplies
02/04/18: Built one of Ken Stone's CGS60 Stompbox Adapters on stripboard
12/04/18: Completed building two Mutable Instruments Peaks (started 10/04/18)
22/04/18: Built two Mutable Instruments Branches
23/04/18: Built another Mutable Instruments Braids
26/04/18: Bought a second-hand Doepfer a138b exponential mixer and second-hand Doepfer LC9 case (linear PSU2 version).
04/05/18: Built a module tester and two Mutable Instruments Grids (finished one with only the jacks and a few ICs to solder as well as the MCU to program on the other)
05/05/18: Built two Mutable Instruments Links and finished the second Mutable Instruments Grids. Half built and programmed two Mutable Instruments Tides
07/05/18: Completed two Mutable Instruments Tides
28/05/18: Completed building another Mutable Instruments Peaks (flashed with Dead Man's Catc firmware and hacked with calibration code)
30/05/18: Completed a Mutable Instruments Elements
01/06/18: Built two Mutable Instruments Shades
05/06/18: Completed three Mutable Instruments Ears. Built two Pusherman Levels (4-way passive attenuators)
15/06/18: Built a Mutable Instruments Warps
17/08/18: Built three Mutable Instruments Kinks
21/08/18: Built two Mutable Instruments Yarns
01/09/18: Built a Mutable Instruments Streams
08/09/18: Built a Mutable Instruments Frames
11/09/18: Built an own design buffered multiple (Minx v2.0)
21/09/18: Bought a PSU3 LC9
22/09/18: Built two Mutable Instruments Clouds
27/09/18: Built three Buranelectrix Dredrums and a Pusherman Levels
02/10/18: Completed two own-design buffered multiples (Minx v2.0)
07/10/18: Built two Mutable Instruments Rings
08/10/18: Bought a stereo microscope (Amscope SE400-Z)
22/10/18: Built two Mutable Instruments Marbles and one Mutable Instruments Ears
25/10/18: Completed a FC ADSR
28/10/18: Built a Mutable Instruments Shelves
02/11/18: Built three Mutable Instruments Plaits
06/11/18: Completed a FC System X Amplifier (VCA)
10/11/18: Built two Mutable Instruments Stages
12/11/18: Built an 808 kick drum for eurorack
20/11/18: Built two Mutable Instruments Blinds
24/11/18: Built a Mutable Instruments Edges
28/11/18: Bought another PSU3 LC9
30/11/18: Built a Mutable Instruments Plaits
02/12/18: Built a DSO150 shell oscilloscope with a eurorack conversion kit
15/12/18: Built another Mutable Instruments Warps
23/12/18: Built a mini Temps Utile
24/12/18: Built a TINRS Tuesday (waiting on one opamp for the second one)
27/12/18: Built another Mutable Instruments Branches (and another Grids - apart from two opamps, which I am waiting for)
06/01/19: Completed another TINRS Tuesday and an MI Grids
09/01/19: Built another Ornament and Crime module
12/01/19: Built another Mutable Instruments Marbles
24/01/19: Built three Mutable Instruments Veils
02/02/19: Finished a Motivation Radio module (esp32-based module to communicate via MIDI and OSC via BLE or WIFI)
08/02/19: Built a Westlicht Per|former sequencer
08/04/19: Built a gBiz Dervish
09/04/19: Finished an Antumbra 6MIX
12/04/19: Built two Mutable Instruments Tides 2s
13/04/19: Built a Sin Phi Miasma
02/05/19: Bought second-hand: Doepfer a131 exponential vca, Doepfer LC3 and a Doepfer PSU3 LC9 case
09/05/19: Built a 4ms SMR and a 4hp triple S&H module "Jinx"
12/08/19: Built another 4hp triple S&H module "Jinx"
14/08/19: Built two Plague Bearers
22/08/19: Built another Mutable Instruments Frames
23/08/19: Built another two Mutable Instruments Frames and two TINRS Wobblers
30/08/19: Built a Fitzgreye 100m-ish Audio Delay.
05/09/19: Built a 4ms SWN
12/09/19: Built another MI Peaks and added a Lorenz Attractor to DMC firmware
19/09/19: Built a Ctag Strampler
24/09/19: Built a MI Shruthi
29/09/19: Built a TINRS Rectangular Thing
02/10/19: Built a TINRS Edgecutter
08/10/19: Built another TINRS Edgecutter
11/10/19: Built a Benjolin
25/10/19: Built a Fates (DIY version of Monome Norns)
27/10/19: Built another MI Warps
05/11/19: Built a Swirls/Lamb (micro Tides clone with sheep firmware installed)
13/11/19: Bought Doepfer a124 Wasp filter and a196 PLL modules
18/11/19: Built an 8-bit Pig GMO
19/11/19: Built a uo_C and a uTU
24/11/19: Built a midipal
26/11/19: Built an own-design as3320-based LPF
03/12/19: Built an own-design as3340-based VCO
06/12/19: Built a Frankinkstides
22/12/19: Built another Streams and a revised version of the Benjolin
30/12/19: Built another own-design as3340-based VCO and another as3320-based lpf, with corrected pcbs.
05/01/20: Built a 3d-printed case
15/01/20: Built a Typhoon (Clouds adaptation with expansions !)
15/01/20: Built an own-design headphone amp
21/01/20: Built an own-design LPG
21/01/20: Built two more VCOs and two more LPFs.
19/01/20: Built an own-design LPG
22/01/20: Built an own-design HPF
22/01/20: Built three more passive mults
15/02/20: Built an x0x heart and pacemaker
02/03/20: Built (repaired) another MI Stages
11/03/20: Built an own-design dual ASR
18/03/20: Bought a pcba MI Shelves
19/03/20: Built an own-design dual VCA
08/04/20: Built a Monome Teletype
20/04/20: Built another 46hp 3d-printed case
05/05/20: Built a Monome Grid clone
15/06/20: Built two more Warps
19/06/20: Built another Rectangular Thing
20/06/20: Built own design Wasp, ADSR and ssi2144 LPF
27/06/20: Built own design SMT Module Tester
07/08/20: Built two more Peaks and two more Rings
06/09/20: Built another headphone amp
09/09/20: Bought another PSU3 LC9
12/09/20: Built another LPG
19/09/20: Built an own design VCA based on 2-sections of MI Blinds
20/09/20: Built an own design matrix mixer
21/09/20: Built an own design Wasp and an ADSR from pcba pcbs
23/09/20: Built a Ryk M185 sequencer
12/10/20: Built a NLC Plague of Demons and a Dual Timbre
13/10/20: Built a Timo Rozendal SDSV+
14/10/20: Built another headphone amp
14/10/20: Built another headphone amp
15/10/20: Built a Dust of Time
16/10/20: Built three more Wasps and a Monome Norns Shield
29/11/20: Built PreenFM2 and a PreenFM3
16/01/21: Built another cvpal
17/01/21: Some progress on tina
06/02/21: Built three more own-design dual VCA
20/02/21: Built another Mutable Instruments Marbles
22/02/21: Built an own-design tzfm vco
02/03/21: Built an own-design (revised) matrix mixer
03/03/21: Finished a 46hp DC-powered 3d-printed case
05/03/21: Built another dual ASR and ssi2144 LPF
14/03/21: Built another MI Plaits from pcba boards
15/03/21: Built two ST Modular Good+Evil modules
21/03/21: Built two more own-design tzfm vco
22/03/21: Built an MI Veils2 and a Ripples2
27/03/21: Built a tzfm vco expander
05/04/21: Built another four MI Plaits from pcba boards and an Antumbra Knit
10/04/21: Built two more own-design tzfm vco
11/04/21: Built a Monome Arc clone
This is the current state of the modular (and how it has grown):
